Teltonika RUTXR1 4G/LTE Cat.6 Dual SIM Wave-2 802.11ac WLAN IoT Router Industriale

MOBILE

Mobile module: 4G (LTE) – Cat 6 up to 300 Mbps, 3G – up to 42 Mbps

SIM switch: 2 SIM cards, auto switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail

Status: Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI,

ICCID

SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto replay

USSD: Supports sending and reading Unstructured Supplementary Service Data messages

Black/White list Operator black/white list

Multiple PDN: Possibility to use different PDNs for multiple network access and services

Band management: Band lock, Used band status display

APN: Auto APN

Bridge mode: Direct connection (bridge) between mobile ISP and device on LAN

WIRELESS

Wireless mode: 802.11b/g/n/ac Wave 2 (WiFi 5) with data transmission rates up to 867 Mbps (Dual Band, MU-MIMO), 802.11r fast transition, Access Point (AP), Station (STA)

WiFi security: WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation

ESSID: ESSID stealth mode

WiFi users: up to 150 simultaneous connections

Wireless Hotspot: Captive portal (Hotspot), internal/external Radius server, built in customizable landing page

ETHERNET

WAN: 1 x WAN port 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

Fiber: 1 x SFP port (cannot work simultaneously with Ethernet WAN port)

LAN: 4 x LAN ports, 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

CONSOLE

Console: RS-232 (RJ45) console port for router configuration and debuging

NETWORK

Routing: Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP)

Network protocols: TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, UPNP, SSH, DHCP, Telnet, SNMP, MQTT, Wake on LAN (WOL), DLNA

VoIP passthrough support: H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring: Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall Port: forwards, traffic rules, custom rules

DHCP: Static and dynamic IP allocation, DHCP Relay, Relayd

QoS / Smart Queue Management (SQM): Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS: Supported >25 service providers, others can be configured manually

Network backup: VRRP, Mobile, Wired, Fiber and WiFi WAN options, each of which can be used as an automatic Failover

Load balancing: Balance Internet traffic over multiple WAN connections

SSHFS: Possibility to mount remote file system via SSH protocol

SECURITY

Authentication: Pre-shared key, digital certificates, X.509 certificates

Firewall: Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention: DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN: Port and tag based VLAN separation

Mobile quota control: Custom data limits for both SIM cards

WEB filter: Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control: Flexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN

OpenVPN: Multiple clients and a server can run simultaneously, 12 encryption methods

OpenVPN Encryption: DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC

IPsec: IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)

GRE: GRE tunnel

PPTP, L2TP: Client/Server instances can run simultaneously, L2TPv3 support

Stunnel: Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN: Method of building scalable IPsec VPNs

SSTP : SSTP client instance support

Zerotier : Zerotier VPN client support

WireGuard: WireGuard VPN client and server support

MODBUS TCP SLAVE

ID filtering: Respond to one ID in range [1;255] or any

Allow remote access: Allow access through WAN

Custom registers: Modbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality

MODBUS TCP MASTER

Supported functions: 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats: 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

MODBUS RTU MASTER (RS232)

Supported baud rates: From 300 to 115200

Supported functions: 01, 02, 03, 04, 05 (only for alarms), 06 (only for alarms), 15 (only for alarms), 16 (only for alarms)

Number of data bits: From 5 to 8

Number of stop bits: 1 or 2

Parity: None, Even, Odd

Flow: None, RTS/CTS, Xon/Xoff

MQTT GATEWAY

Gateway: Allows sending commands and receiving data from Modbus Master trough MQTT broker

DNP3

Supported modes: TCP Master, DNP3 Outstation

DATA TO SERVER

Protocols: HTTP(S), MQTT, Azure MQTT, Kinesis

MONITORING & MANAGEMENT

WEB UI HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log

FOTA: Firmware update from server, automatic notification

SSH: SSH (v1, v2)

SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call: Reboot, Status, Mobile data on/off, Output on/off

TR-069  OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT: MQTT Broker, MQTT publisher

SNMP: SNMP (v1, v2, v3), SNMP Trap

JSON-RPC: Management API over HTTP/HTTPS

Modbus: Modbus TCP status/control

RMS: Teltonika Remote Management Systems (RMS)

IoT PLATFORMS

Clouds of things: Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx: Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity: Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP

Azure IoT Hub; Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server

SYSTEM CHARACTERISTICS

CPU: Quad-core ARM Cortex A7, 717 MHz

RAM: 256 MB, DDR3

FLASH storage: 256 MB, SPI Flash

FIRMWARE/CONFIGURATION

WEB UI: Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA: Update FW/configuration from server

RMS: Update FW/configuration for multiple devices at once

Keep settings: Update FW without losing current configuration

FIRMWARE CUSTOMIZATION

Operating system: RutOS (OpenWrt based Linux OS)

Supported languages: Busybox shell, Lua, C, C++

Development tools: SDK package with build environment provided

SERIAL

RS232: RJ45 connector, full RS232 (with RTS, CTS)

Serial functions: Console (active by default), Modbus gateway, Modbus RTU master, Serial OverIP, Modem mode (Full or partial), Ntrip client

USB

Data rate: USB 2.0

Applications: Samba share, USB-to-serial

External devices: Possibility to connect external HDD, flash drive, additional modem, printer

Storage formats: FAT, FAT32, NTFS

POWER

Connector: 2 x 4 pin industrial DC power sockets for main and redundancy power sources

Input voltage range: 9 – 50 VDC, reverse polarity protection, voltage surge/transient protection

Power consumption: idle: <3W, max: 18W

PHYSICAL INTERFACES

Ethernet: 5 x RJ45 ports, 10/100/1000 Mbps

Console : 1 x RJ45, RS232 communication

Fiber :1 x SFP port

Status LEDs: 2 x WAN type, 2 x Mobile connection type, 3 x Mobile signal strength, 2 x active SIM, 10 x Ethernet status, 2 x Console status, 2 x Power

SIM: 2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders

Power: 2 x 4 pin DC connector

Antennas: 2 x SMA for LTE, 2 x RP-SMA for WiFi

USB: 1 x USB A port for external devices

Reset: Reboot/User default reset/Factory reset button

Other: 1 x Grounding screw, 1 x lock

PHYSICAL SPECIFICATION

Casing material: Full steel housing

Dimensions (W x H x D): 272 x 42.6 x 122.6 mm

Weight: 1050 g

Mounting options: Rack mounting, flat surface placement

OPERATING ENVIRONMENT

Operating temperature: -40°C to +75°C

Operating humidity: 10 % to 90 % non-condensing